Search

SearchSearch

Need help with an alternative? Contact an expert

Back to overview

KINS' BLUE HT Pro

Ultimate solution for tube cutting performance

Unlock the full potential of your tube cutting operations with the KINS’ BLUE HT Pro saw blade. With cutting speeds up to 300 m/min at very high feed rates, the PVD coated carbide tipped KINS’ BLUE HT Pro is your optimal solution for high volume and high tensile tube applications.

It has specifically been designed for cutting all types of high tensile tubes with a high output and will perform at its best at tensile strengths between 1,000 – 1,800 N/mm² at a wide range of demanding tube applications and steel grades. Typical products are drive shafts, twist beams, camshafts, suspensions and differentials.

Advantages of KINS’ BLUE HT Pro saw blades

Suitable for all types of high-tensile tubes
Specifically designed for cutting high tensile tubes with a high output
Higher blade life, especially when cutting higher tensile strength tubes
Very high feed rates
Because the cut surface is as close to the end stage as possible, you will minimize or avoid post-machining, save cycle time and tool costs

ACHIEVE A FLAWLESS SURFACE FINISH

Achieve an almost flawless surface finish that meets the highest standards of your industry and minimize or avoid post-machining, by saving cycle time and tool costs.

Applications for KINS’ BLUE HT Pro

Cutting high tensile tubes with high output (best performing between 1,000 – 1,800 N/mm²)
Cutting speeds up to 300 m/min
Tooth load ranging from: 0.035 – 0.20 mm/tooth
When focussing on output, using high parameters is advised.
When focussing on blade life, using regular parameters is advised

Applications for KINS’ BLUE HT Pro include:

Seating components, headrests
Sleeves, bushings
Drive shafts, side shafts, half shafts
Twistbeam
Chassis / body structures, stabilizer bars, instrumental panel beams
Camshafts,
Suspensions, shock absorber parts
Steering mechanics
Fittings, couplings
Differentials

Typical steel grades for KINS’ BLUE HT Pro

Carbon steel (E355 +C)
High Carbon, high tensile
‘Sticky’ materials
High Strength Low Alloy (HSLA)
Advanced High Strength Steel (AHSS)
Manganese (Mn) alloyed
Boron (B) alloyed
Docol Dual Phase
XPF grades
Specifically: 22MnB5 / 26MnB5 / 27MnB5, 34CrMo4 / 34CrMo4-HC / 34CrMo4-LC / 34MnB5, MW1000L / MW700L

Worldwide network

Find your distributorGet your saw blades

TYPICAL MACHINES

Manufacturer	Machine type
Rattunde	ACS series
RSA	Rasacut
Sinico	Top
Bewo	DCH / SCF (single/double)
Soco	SA Series
Adige / BLM	TS/CM series

STANDARD Range KINS’ BLUE HT Pro

Diameter (mm)	Kerf (mm)	Bore hole (mm)	Pinholes	No. of teeth (Z)
315	2,3 / 2,0	32	4 / 9 / 50 / 4 / 12 / 64	100
315	2,3 / 2,0	32	4 / 9 / 50 / 4 / 12 / 64	120
315	2,3 / 2,0	40	4 / 9 / 50 / 4 / 12 / 64	100
315	2,3 / 2,0	40	2 / 9 / 55 / 4 / 12 / 64	120
350	2,7 / 2,5	50	4 / 16 / 80	100
350	2,7 / 2,5	50	4 / 16 / 80	120
350	2,7 / 2,5	50	4 / 16 / 80	140